Hardware Design Engineer – Automotive Electrification

Hardware Design Engineer Automotive Electrification

RGS ID: 10836849

Location: Pune

Experience: 4 8 Years

Skill: EIS Embedded Digital Hardware Design and Development

Job Summary

We are looking for an experienced Hardware Design Engineer with strong expertise in embedded hardware design and development for automotive electronics and electrification products. The candidate will be responsible for requirement analysis, hardware architecture, circuit design, simulation, prototyping, testing, debugging, and design documentation throughout the complete hardware development lifecycle.

Key Responsibilities

Analyze product requirements and translate them into hardware design specifications.
Design and develop automotive electronic control modules (ECUs) and electrification products.
Develop analog and mixed-signal circuits, including OP-AMP, ADC, data acquisition, sensor interface, and signal-conditioning circuits.
Design microcontroller/microprocessor-based hardware using 16/32-bit MCUs/processors, ADCs, SDRAM/DDR, Flash, and related peripherals.
Design and develop power electronics circuits, including linear and switch-mode power supplies, Buck/Boost converters, DC-DC converters, inverters, and AC/DC power supplies.
Work with IGBTs and MOSFETs for high-power/high-wattage applications.
Design and integrate communication interfaces such as UART, I2C, SPI, RS485, USB, CAN, and Ethernet.
Define and review multilayer PCB layouts, component placement, routing, grounding, and power distribution based on performance and EMI/EMC requirements.
Apply EMI/EMC design principles and support compliance testing and troubleshooting.
Select and integrate automotive sensors such as Exhaust Gas Temperature, Humidity, and other engine/after-treatment sensors.
Perform circuit simulations and design calculations using MATLAB/Simulink, PSpice, LTspice, and Mathcad.
Conduct board bring-up, prototyping, testing, debugging, and validation using DSO/oscilloscope, logic analyzers, emulators, and other lab equipment.
Perform basic signal integrity analysis and address PCB-related signal integrity issues.
Support DFM/DFT, product certification, and compliance requirements.
Prepare and maintain hardware design specifications, schematics, BOMs, test reports, validation reports, and other technical documentation.
Collaborate with cross-functional teams including firmware, mechanical, systems, testing, manufacturing, and project management teams.
Support the complete hardware development lifecycle from requirements and design through prototyping, validation, release, and production.

Must-Have Skills

4 8 years of experience in embedded hardware design and development.
Strong experience in automotive electronics/control module design and electrification products.
Hands-on experience with analog circuit design, OP-AMP, ADC, sensor interfaces, and signal conditioning.
Experience in microcontroller/microprocessor-based hardware design.
Strong knowledge of power electronics, DC-DC converters, Buck/Boost converters, inverters, and SMPS.
Experience with IGBT and MOSFET-based high-power designs.
Knowledge of UART, I2C, SPI, RS485, USB, CAN, and Ethernet.
Good understanding of multilayer PCB design, layout, routing, grounding, and EMI/EMC.
Experience with MATLAB/Simulink, PSpice/LTspice, or Mathcad.
Experience in automotive sensor selection and interface design.
Strong hardware testing, debugging, and board bring-up experience.
Good communication and project management skills.

Good-to-Have Skills

Experience with Altium, Zuken, Cadence Capture, or similar schematic/design tools.
Knowledge of HyperLynx, Cadence SI, or other signal integrity tools.
Experience with DSO/oscilloscope, logic analyzer, emulators, and hardware debugging tools.
Knowledge of automotive/industrial standards such as IEC, UL, CE, and CISPR.
Experience with DFM and DFT guidelines.
Experience in mixed-signal designs involving MCUs/processors, SDRAM, DDR, Flash, ADC, etc.
Automotive product development experience.
Exposure to hardware validation and certification processes.

Key Deliverables / Expectations

Requirement Analysis Analyze system/product requirements and define hardware requirements and architecture.
Design & Development Develop schematics, circuits, power supplies, interfaces, PCB designs, and prototypes.
Prototyping & Testing Perform board bring-up, validation, debugging, testing, and EMI/EMC support.
Design Documentation Prepare and maintain schematics, BOMs, design specifications, test procedures, reports, and other technical documents.

Preferred Domain

Automotive Electronics | Automotive Electrification | ECU/Control Modules | Embedded Hardware | Power Electronics

Send me the resumes at pramoda@galaxyitech.com
Show more Show less