QG
Hardware Design Engineer
Accepting applicationsQuest Global · Thiruvananthapuram, Kerala, India
Full-Time Mid ARMAnalogCadenceEthernetFPGA
Estimated market salary
₹9-14 LPA
This is a SiliconBoard market estimate, not an employer-posted salary.
Posted
1d ago
Category
Design
Experience
Mid
Country
India
Job Requirements
Technical Skills
Circuit Design & Development: Design circuits to meet HW requirements. Components Selection and good in selection of the equivalent components, Create, simulate, and debug Power circuits, analog, digital, and mixed-signal circuits for electromechanical medical devices.
Schematic & PCB Layout: Perform schematic capture and guide PCB layout engineers, adhering to design rules for high-speed, high-density, and low-power, miniature, or wearable assemblies.
Microcontrollers/Interfaces: Experience with ARM Cortex, TI, NXP, or STM32 microcontrollers. Deep knowledge of communication protocols: I2C, SPI, UART, CAN, USB, Ethernet. Etc.
FPGA: Exposure to schematic design using Xilinx / Altera FPGAs
Analog/Digital Expertise: Signal conditioning, noise reduction techniques, ADC/DAC interfacing, and power supply design.
Lab Equipment: Hands-on experience with Oscilloscopes, Logic Analyzers, Spectrum Analyzers, and Digital Multi meters for troubleshooting.
Tools: High proficiency in Schematics, PCB design tools such as Altium Designer, Cadence OrCAD. Etc.
BOM Analysis : Component optimization & Qualification, Cost & Lifecycle Optimization, Regulatory Documentation
Job Responsibilities
Understand Hardware Requirement Specification and design hardware to meet the requirements
Design processor and FPGA based boards
Execute HW development activities independently as assigned
Technical ownership of the hardware for the assigned module / board
Schematic, PCB Design Support, Board bringup
Provide HW support during system integration activities
Redesign for cost optimisations
Support team in identifying root cause and fixing issues
Provide support during environmental testing and EMI/EMC testing
Would Be a Plus
Exposure to high-speed interfaces
Experience in power optimizations
Experience implementing USB or Ethernet
Experience developing HW for using FPGA
Exposure to stepper motor control based designs
Communication
Good and strong verbal and written communication to involved stakeholders
Should be able to conduct fruitful discussion with hardware and software team
Preferred Qualification
Bachelor degree in Engineering - Electronics Engineering
Years of Experience : 3 - 6 Years
Job Location
Trivandrum
Show more Show less
Technical Skills
Circuit Design & Development: Design circuits to meet HW requirements. Components Selection and good in selection of the equivalent components, Create, simulate, and debug Power circuits, analog, digital, and mixed-signal circuits for electromechanical medical devices.
Schematic & PCB Layout: Perform schematic capture and guide PCB layout engineers, adhering to design rules for high-speed, high-density, and low-power, miniature, or wearable assemblies.
Microcontrollers/Interfaces: Experience with ARM Cortex, TI, NXP, or STM32 microcontrollers. Deep knowledge of communication protocols: I2C, SPI, UART, CAN, USB, Ethernet. Etc.
FPGA: Exposure to schematic design using Xilinx / Altera FPGAs
Analog/Digital Expertise: Signal conditioning, noise reduction techniques, ADC/DAC interfacing, and power supply design.
Lab Equipment: Hands-on experience with Oscilloscopes, Logic Analyzers, Spectrum Analyzers, and Digital Multi meters for troubleshooting.
Tools: High proficiency in Schematics, PCB design tools such as Altium Designer, Cadence OrCAD. Etc.
BOM Analysis : Component optimization & Qualification, Cost & Lifecycle Optimization, Regulatory Documentation
Job Responsibilities
Understand Hardware Requirement Specification and design hardware to meet the requirements
Design processor and FPGA based boards
Execute HW development activities independently as assigned
Technical ownership of the hardware for the assigned module / board
Schematic, PCB Design Support, Board bringup
Provide HW support during system integration activities
Redesign for cost optimisations
Support team in identifying root cause and fixing issues
Provide support during environmental testing and EMI/EMC testing
Would Be a Plus
Exposure to high-speed interfaces
Experience in power optimizations
Experience implementing USB or Ethernet
Experience developing HW for using FPGA
Exposure to stepper motor control based designs
Communication
Good and strong verbal and written communication to involved stakeholders
Should be able to conduct fruitful discussion with hardware and software team
Preferred Qualification
Bachelor degree in Engineering - Electronics Engineering
Years of Experience : 3 - 6 Years
Job Location
Trivandrum
Show more Show less